Equipment
Surgery & implantology
7 products in this category
New
IMPNAVIMPNAV is an AI-assisted dynamic navigation system for dental implant surgery that links digital preoperative planning with real-time surgical navigation. Planning is built on the patient’s CT data; during surgery an optical tracking system follows the instrument tip and shows the clinician, in 3D, the drilling position, direction and depth against the planned implant position.
Aurora-SA combined laser system: Er:YAG at 2940 nm together with a diode laser at 980, 650 and 450 nm. That combination is the reason to buy a unit like this — Er:YAG is absorbed by water and works on hard tissue and bone without heat building up, while the diode handles soft tissue. One unit therefore covers cavity preparation, bone surgery and soft-tissue cutting. Two laser modes, and the unit rolls between rooms on castors. Class IV — protective eyewear and a room safety protocol are required. Supplied by JK Dent with training and ongoing service.
iLaser I PlusA desktop diode laser with three wavelengths — 450, 650 and 980 nm — in one instrument. The three are not alternatives but complements: each is absorbed by different tissue, so a single unit covers a wider range of indications than a single-wavelength device. Class IV — protective eyewear is required for staff and patient, along with a room safety protocol. Through JK Dent — with warranty and in-clinic service.
iLaser IA diode laser from Soga for soft-tissue use in the dental clinic: cutting, coagulation and periodontal treatment, with a thin optical fiber that reaches areas mechanical instruments struggle with. It suits anyone who folds soft-tissue treatment into routine work and wants precise power control per indication. Supply, installation, staff training and maintenance by JK Dent.
iLaser IIA pen-body diode laser weighing 106 g with an internal battery — no benchtop unit and no mains cable. Its 980 nm wavelength is well absorbed by water and hemoglobin, so it cuts soft tissue and coagulates in the same pass; the cut comes out clean without bleeding that obscures the field. Continuous power reaches 3 W with a 5 W pulse peak, adjustable from 0.5 W upward, with 200 and 400 μm fibers and a red aiming beam. Class IV — protective eyewear is required for staff and patient. Supplied by JK Dent with training and ongoing service.
MotorSurgA surgical implant motor with a torque range of 5 to 80 N·cm and speeds from 200 to 40,000 rpm — meaning one unit handles both fast drilling and slow high-torque seating without swapping instruments mid-surgery. Torque feedback is shown in real time, which is what lets you feel bone resistance before it becomes a problem. The water pump delivers up to 130 mL/min, eight programs are stored, and calibration takes one button. The 20:1 contra-angle is lit at adjustable brightness. Supply, calibration and maintenance — JK Dent’s responsibility.
B1A piezo ultrasonic unit with five working modes: bone, endo, perio, custom and clean. Piezo cuts mineralized bone while leaving soft tissue — nerve, membrane, vessels — largely untouched, which is why it is the preferred instrument for sinus lift, bone harvesting and implant exposure. Separate control of power and coolant lets you bring heat down without giving up cutting force. An end-of-day cleaning cycle flushes the fluid lines. Supplied by JK Dent, with training on its use and follow-up service.
IMPNAVIMPNAV is an AI-assisted dynamic navigation system for dental implant surgery that links digital preoperative planning with real-time surgical navigation. Planning is built on the patient’s CT data; during surgery an optical tracking system follows the instrument tip and shows the clinician, in 3D, the drilling position, direction and depth against the planned implant position.
Aurora-SA combined laser system: Er:YAG at 2940 nm together with a diode laser at 980, 650 and 450 nm. That combination is the reason to buy a unit like this — Er:YAG is absorbed by water and works on hard tissue and bone without heat building up, while the diode handles soft tissue. One unit therefore covers cavity preparation, bone surgery and soft-tissue cutting. Two laser modes, and the unit rolls between rooms on castors. Class IV — protective eyewear and a room safety protocol are required. Supplied by JK Dent with training and ongoing service.
iLaser I PlusA desktop diode laser with three wavelengths — 450, 650 and 980 nm — in one instrument. The three are not alternatives but complements: each is absorbed by different tissue, so a single unit covers a wider range of indications than a single-wavelength device. Class IV — protective eyewear is required for staff and patient, along with a room safety protocol. Through JK Dent — with warranty and in-clinic service.
iLaser IA diode laser from Soga for soft-tissue use in the dental clinic: cutting, coagulation and periodontal treatment, with a thin optical fiber that reaches areas mechanical instruments struggle with. It suits anyone who folds soft-tissue treatment into routine work and wants precise power control per indication. Supply, installation, staff training and maintenance by JK Dent.
iLaser IIA pen-body diode laser weighing 106 g with an internal battery — no benchtop unit and no mains cable. Its 980 nm wavelength is well absorbed by water and hemoglobin, so it cuts soft tissue and coagulates in the same pass; the cut comes out clean without bleeding that obscures the field. Continuous power reaches 3 W with a 5 W pulse peak, adjustable from 0.5 W upward, with 200 and 400 μm fibers and a red aiming beam. Class IV — protective eyewear is required for staff and patient. Supplied by JK Dent with training and ongoing service.
MotorSurgA surgical implant motor with a torque range of 5 to 80 N·cm and speeds from 200 to 40,000 rpm — meaning one unit handles both fast drilling and slow high-torque seating without swapping instruments mid-surgery. Torque feedback is shown in real time, which is what lets you feel bone resistance before it becomes a problem. The water pump delivers up to 130 mL/min, eight programs are stored, and calibration takes one button. The 20:1 contra-angle is lit at adjustable brightness. Supply, calibration and maintenance — JK Dent’s responsibility.
B1A piezo ultrasonic unit with five working modes: bone, endo, perio, custom and clean. Piezo cuts mineralized bone while leaving soft tissue — nerve, membrane, vessels — largely untouched, which is why it is the preferred instrument for sinus lift, bone harvesting and implant exposure. Separate control of power and coolant lets you bring heat down without giving up cutting force. An end-of-day cleaning cycle flushes the fluid lines. Supplied by JK Dent, with training on its use and follow-up service.
Contact us
A site visit, measurements and an initial plan with a price range — no obligation.
Leave a detailed message
Even outside business hours — we will get back to you.